Determining a Suitable Location for Wind Turbines Using Inverse Solution and Mast Data in a Mountainous Terrain

Document Type : Research Article

Authors

Department of Mechanical Engineering, Tafresh University, Tafresh, Iran

Abstract

Optimum design of a wind farm will ensure high output rated power and low operating costs. The aim of this study was to determine the optimum location to install a wind turbine in a mountainous terrain using computational fluid dynamics. This purpose is achieved by employing inverse method, with the objective of maximizing the efficiency of the turbines while minimizing loss expenses caused by placing them in a less optimum region. Boundary conditions are determined by steepest decent optimization method. 2-D mountain geometry alongside the mast data installed on the flat area are the references of evaluating the performance of the proposed method in this paper. Results indicated that in current turbulent flow, separation occurs in atmospheric boundary layer due to an adverse pressure gradient. Furthermore resultant pressure contours demonstrated that air flow pressure decreases over the hill and its minimum value is reported at the top of the hill, thus adverse pressure gradient happens in the back hill. Simulation results revealed a considerable difference among the power outputs of the same turbine installed at different points of the domain. Turbine performance in the initial installation point and in the point derived from the algorithm is then compared. The performance reported is nineteen times better in the new suggested location.

Keywords

Main Subjects


[1] K. Kaygusuz, Wind energy: progress and potential, Energy sources, 26(2) (2004) 95-105.
[2] M. Ritter, L. Deckert, Site assessment, turbine selection, and local feed-in tariffs through the wind energy index, Applied Energy, 185 (2017) 1087-1099.
[3] P. Mittal, K. Mitra, Decomposition based multi-objective optimization to simultaneously determine the number and the optimum locations of wind turbines in a wind farm, IFAC-PapersOnLine, 50(1) (2017) 159-164.
[4] T. Burton, N. Jenkins, D. Sharpe, E. Bossanyi, Wind energy handbook, John Wiley & Sons, 2011.
[5] H. Cetinay, F.A. Kuipers, A.N. Guven, Optimal siting and sizing of wind farms, Renewable Energy, 101 (2017) 51-58.
[6] S. Yan, S. Shi, X. Chen, X. Wang, L. Mao, X. Liu, Numerical simulations of flow interactions between steep hill terrain and large scale wind turbine, Energy, (2018).
[7] C.J. Desmond, S.J. Watson, P.E. Hancock, Modelling the wind energy resource in complex terrain and atmospheres. Numerical simulation and wind tunnel investigation of non-neutral forest canopy flow, Journal of Wind Engineering and Industrial Aerodynamics, 166 (2017) 48-60.
[8] A. Russell, Computational fluid dynamics modeling of atmospheric flow applied to wind energy research, (2009).
[9] H. Ertürk, O.A. Ezekoye, J.R. Howell, Boundary condition design to heat a moving object at uniform transient temperature using inverse formulation, Journal of manufacturing science and engineering, 126(3) (2004) 619-626.
[10] R. Mehdipour, A. Ashrafizadeh, K. Daun, C. Aghanajafi, Dynamic optimization of a radiation paint cure oven using the nominal cure point criterion, Drying Technology, 28(12) (2010) 1405-1415.
[11] R. Mehdipour, C. Aghanajafi, A. Ashrafizadeh, Optimal design of radiation paint cure ovens using a novel objective function, Pigment & Resin Technology, 41(4) (2012) 240-250.
[12] M.A. Mahmoud, A.E. Ben-Nakhi, Neural networks analysis of free laminar convection heat transfer in a partitioned enclosure, Communications in Nonlinear Science and Numerical Simulation, 12(7) (2007) 1265-1276.
[13] H. Ertürk, O.A. Ezekoye, J.R. Howell, The Use of Inverse Formulation in Design and Control of Transient Radiant Systems, in: Proceedings of International Heat Transfer Conference, Grenoble, France, 2002.
[14] F.H. França, O.A. Ezekoye, J.R. Howell, Inverse boundary design combining radiation and convection heat transfer, Journal of heat transfer, 123(5) (2001) 884-891.
[15] J. Xiao, J. Li, Q. Xu, Y. Huang, H.H. Lou, ACS–based dynamic optimization for curing of polymeric coating, AIChE journal, 52(4) (2006) 1410-1422.
[16] A. Ashrafizadeh, R. Mehdipour, C. Aghanajafi, A hybrid optimization algorithm for the thermal design of radiant paint cure ovens, Applied Thermal Engineering, 40 (2012) 56-63.
[17] H.G. Kim, C.M. Lee, H.C. Lim, N.H. Kyong, An experimental and numerical study on the flow over two-dimensional hills, Journal of Wind Engineering and Industrial Aerodynamics, 66(1) (1997) 17-33.
[18] H.G. Kim, V. Patel, C.M. Lee, Numerical simulation of wind flow over hilly terrain, Journal of wind engineering and industrial aerodynamics, 87(1) (2000) 45-60.
[19] D. Fallo, Wind energy resource evaluation in a site of central Italy by CFD simulations, UNIVERSITÀ DEGLI STUDI DI CAGLIARI. Cagliari, Italia, (2007).
[20] P. Fang, M. Gu, J. Tan, B. Zhao, D. Shao, Modeling the neutral atmospheric boundary layer based on the standard k-ε turbulent model: modified wall function, Wind Engineering, (2009).
[21] S. Cao, T. Wang, Y. Ge, Y. Tamura, Numerical study on turbulent boundary layers over two-dimensional hills—effects of surface roughness and slope, Journal of wind engineering and industrial aerodynamics, 104 (2012) 342-349.
[22] Z. Liu, T. Ishihara, T. Tanaka, X. He, LES study of turbulent flow fields over a smooth 3-D hill and a smooth 2-D ridge, Journal of Wind Engineering and Industrial Aerodynamics, 153 (2016) 1-12.
[23] G. Mosetti, C. Poloni, B. Diviacco, Optimization of wind turbine positioning in large windfarms by means of a genetic algorithm, Journal of Wind Engineering and Industrial Aerodynamics, 51(1) (1994) 105-116.
[24] S. Grady, M. Hussaini, M.M. Abdullah, Placement of wind turbines using genetic algorithms, Renewable energy, 30(2) (2005) 259-270.
[25] A. Emami, P. Noghreh, New approach on optimization in placement of wind turbines within wind farm by genetic algorithms, Renewable Energy, 35(7) (2010) 1559-1564.
[26] C. Wan, J. Wang, G. Yang, X. Li, X. Zhang, Optimal micro-siting of wind turbines by genetic algorithms based on improved wind and turbine models, in: Decision and Control, 2009 held jointly with the 2009 28th Chinese Control Conference. CDC/CCC 2009. Proceedings of the 48th IEEE Conference on, IEEE, 2009, pp. 5092-5096.
[27] E. EU-FP, Wind loads on solar energy roofs, Heron, 52(3) (2007) 201.
[28] Z. Baniamerian, R. Mehdipour, Studying Effects of Fence and Sheltering on the Aerodynamic Forces Experienced by Parabolic Trough Solar Collectors, Journal of Fluids Engineering, 139(3) (2017) 031103.
[29] J.A. Peterka, Z. Tan, B. Bienkiewicz, J. Cermak, Wind loads on heliostats and parabolic dish collectors: Final subcontractor report, Solar Energy Research Inst., Golden, CO (USA), 1988.
[30] A. Ashrafizadeh, G.D. Raithby, G. Stubley, Direct design of shape, Numerical Heat Transfer: Part B: Fundamentals, 41(6) (2002) 501-520.
[31] K. Daun, H. Erturk, J.R. Howell, Inverse design methods for high-temperature systems, Arabian Journal for Science and Engineering, 27(2) (2002) 3-48.
[32] M. Zanganeh, V. Khalajzadeh, Validation of the WAsP model for a terrain surrounded by mountainous region, in: Proceedings of World Academy of Science, Engineering and Technology, 2011, pp. 379-383.