Residual Stresses Measurement in UIC 60 Rail by Ring-Core Method and Sectioning Technique

Document Type : Research Article

Authors

Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran.

Abstract

The measurement of residual stress in rail foot, according to manufacturing standards is mandatory. In this study, the ring-core method and the sectioning technique are used to measure the residual stresses. A calibration technique for the ring-core method has been explained and simulated by the finite element analysis. The calibration coefficient has been determined for certain parameters and various depths of the annular groove. The ring-core method has been simulated for the uniaxial residual stress field and it is observed that the maximum error in the maximum principal residual stress was about 13% which is about 5% of material yield stress. The residual stresses have been measured at the UIC 60 rail foot by the ring-core method and the sectioning technique, and the results are in a good agreement with earlier investigations in this field. Also, it has been indicated that maximum residual stresses on the rail foot are not in the longitudinal direction and in the subsurface of the rail foot, the maximum principal direction coincides with the longitudinal direction. Both methods indicated tensile residual stresses on the rail foot, but the ring-core method predicted 27% higher longitudinal residual stress on the rail foot in comparing with the sectioning technique.

Keywords


[1] C. Betegon Biempica, J. J. del Coz Diaz, P. J. Garcia Nieto, I. Penuelas Sanchez, Nonlinear Analysis of Residual Stresses in a Rail Manufacturing Process by FEM, Applied Mathematical Modelling 33 (2009) 34-53.
[2] M. A. Moazam, A. Ghasemi, M. Moradi, H. Monajatizadeh, Pattern of Residual Stress in Rail by FEM Analysis and Strain Gage Sectioning Technique, Iranian Journal of Materials Forming 2(1) (2015) 1-10.
[3] M. Sedighi, M. Honarpisheh, Investigation of cold rolling influence on near surface residual stress distribution in explosive welded multilayer, Strength of Materials 44(6) (2012), 693-698.
[4] M. Kotobi, M. Honarpisheh, Uncertainty analysis of residual stresses measured by slitting method in equal-channel angular rolled Al-1060 strips, The Journal of Strain Analysis for Engineering Design 52(2) (2017), 83-92.
[5] M. Honarpisheh, E. Haghighat, M. Kotobi, Investigation of residual stress and mechanical properties of equal channel angular rolled St12 strips, Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications (2016) https://doi.org/10.1177/1464420716652436.
[6] M. Kotobi, M. Honarpisheh, Experimental and numerical investigation of through-thickness residual stress of laser-bent Ti samples, The Journal of Strain Analysis for Engineering Design 52(6) (2017) 347-355.
[7] I. Alinaghian, M. Honarpisheh, S. Amini, The influence of bending mode ultrasonic-assisted friction stir welding of Al-6061-T6 alloy on residual stress, welding force and macrostructure, The International Journal of Advanced Manufacturing Technology 95 (5-8) (2018) 2757-2766.
[8] M. Honarpisheh, F. Nazari, Uncertainty analysis of contour method in the hot extruded Aluminum specimens, Modares Mechanical Engineering, 17(5) (2017) 439-445.
[9] J. Basu, S. L. Srimani D. S. Gupta, Rail Behavior During Cooling after Hot Rolling, The Journal of Strain Analysis
for Engineering Design, 39(1) (2004) 15-24.
[10] G. Schleinzer, F. D. Fischer, Residual stress formation during the roller straightening of railway rails, International Journal of Mechanical Sciences 43(10) (2001) 2281-2295.
[11] W. H. Hodgson, Residual Stress in Rail, Rail Quality and Maintenance for Modern Railway Operation, Dordrecht, Netherlands, Kluwer Academic Publishers (1993) 61-73.
[12] P. J. Webster, G. Mills, X. Wang, W. P. Xang, Residual Stress Measurements in Rails by Neutron Diffraction, Netherlands, Kluwer Academic Publishers (1993) 307-314.
[13] G. Schleinzer, F. D. Fischer, Residual stresses in new rails, Materials Science and Engineering: A 288(2) (2000) 280-283.
[14] S. L. Srimani, J. Basu, An Investigation for Control of Residual Stress in Roller-Straightened Rails, The Journal of Strain Analysis for Engineering Design 38(3) (2003) 261-268.
[15] European Standard, prEN 13674-1, Railway Applications-Track-Rail, Part 1: Vignole railway rails 46 kg/m and above, Nov. 2002.
[16] J. W. Ringsberg, H. Bjarnehed, A. Johansson, B. L. Josefson, Rolling contact fatigue of rails-finite element modelling of residual stresses, strains and crack initiation, Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit 214(1) (2000) 7-19.
[17] M. E. Turan, S. Ozcelik, F. Husem, H. Ahlatci, Y. Sun, I. Tozlu, The effect of head hardening process on the residual stress of rails, Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit 232(2) (2018) 589-595.
[18] G. Donzella, M. Scepi, L. Solazzi, F. Trombini, The effect of block braking on the residual stress state of a solid railway wheel.” Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit 212(2) (1998) 145-158.
[19] J. Václavík, O.Weinberg, P.Bohdan, J.Jankovec, S. Holý. Evaluation of Residual Stresses using Ring Core Method, EPJ Web of Conferences 16 (2010) 44004.
[20] K. Maslákováa, F. Trebuna, P. Frankovský, M. Binda, Applications of the strain gauge for determination of residual stresses using Ring-core method, Procedia Engineering 48 (2012) 396-401.
[21] F. Mendaa, P. Šarga, T. Lipták, F. Trebuna, Analysis of the geometric shape of the cutter in Ring-Core measurement, Procedia Engineering 96 (2014) 289-293.
[22] C. Bouffioux, R. Pesci, R. Boman, N. Caillet, J. P. Ponthot, A. M. Habraken, Comparison of residual stresses on long rolled profiles measured by X-ray diffraction ,ringcore and the sectioning methods and simulated by FE method, Thin Walled Structures104 (2016) 126-134.
[23] A. Misra, H. A. Peterson, Examination of the ring method for determination of residual stresses, Experimental Mechanics 21(7) (1981) 268-272.
[24] S. Keil, Experimental determination of residual stresses with the ring-core method and an on line measuring, Experimental Technique 16(5) (1992) 17-24.
[25] A. Civin, M. Vlk, Analysis of Calibration Coefficients for Incremental Strain Method Used for Residual Stress Measurement by Ring-Core Method, Applied Mechanics (2010) 25-28.
[26] ABAQUS Users Manual, Version 6.2, Hibbit, Karlsson and Sorensen Inc.
[27] Tokyo Sokki KenkyujoCo, Ltd., TML Strain gage cataloge, Accessed on 1 Aguest 2016; http://www.tml.jp/e.